![how to setup router on a stick how to setup router on a stick](http://2.bp.blogspot.com/-Wra9Mixp_ac/VREzx6SrXTI/AAAAAAAAAJM/OYryInQMmWA/w1200-h630-p-k-no-nu/topolgy.jpg)
- HOW TO SETUP ROUTER ON A STICK HOW TO
- HOW TO SETUP ROUTER ON A STICK SOFTWARE
- HOW TO SETUP ROUTER ON A STICK PASSWORD
HOW TO SETUP ROUTER ON A STICK PASSWORD
When prompted, enter the Username and Password information for Xauth and click OK in order to connect to the remote network. Click Save.Ĭlick on the connection you would like to use and click Connect from the VPN Client main window. access-list 144 permit ip 192.168.1.0 0.0.0.255 any !- Configures the route map to match the interesting traffic (access list 144) !- and routes the traffic to next hop address 10.11.0.2.Ĭomplete these steps in order to configure the VPN Client 4.8.Ĭhoose Start > Programs > Cisco Systems VPN Client > VPN Client.Ĭlick New in order to launch the Create New VPN Connection Entry window.Įnter the name of the Connection Entry along with a description, enter the outside IP address of the router in the Host box, and enter the VPN Group name and password. !- Interesting traffic used for policy route. !- The access list is used to specify which traffic is to be translated for the !- outside Internet.
![how to setup router on a stick how to setup router on a stick](https://www.routerfreak.com/wp-content/uploads/ROAS-figure-1.jpg)
ip nat inside source list 101 interface FastEthernet1/0 overload !- Enables Network Address Translation (NAT) !- of the inside source address that matches access list 101 !- and gets PATed with the FastEthernet IP address. !- Create a pool of addresses to be !- assigned to the VPN Clients. !- Apply the crypto map on the interface. !- Create the loopback interface for the VPN user traffic. crypto map clientmap client authentication list userauthenĬrypto map clientmap isakmp authorization list groupauthorĬrypto map clientmap client configuration address respondĬrypto map clientmap 10 ipsec-isakmp dynamic dynmap !- Create the actual crypto map, !- and apply the AAA lists that were created earlier. !- Create a dynamic map and apply !- the transform set that was created earlier. crypto ipsec transform-set myset esp-3des esp-md5-hmac !- Create the Phase 2 Policy for actual data encryption. crypto isakmp client configuration group vpnclient Group 2 !- Create a group that is used to specify the !- WINS and DNS server addresses to the VPN Client, !- along with the pre-shared key for authentication. !- Create an Internet Security Association and !- Key Management Protocol (ISAKMP) policy for Phase 1 negotiations. !- For local authentication of the IPsec user, !- create the user with a password. aaa authorization network groupauthor local aaa authentication login userauthen local !- In order to enable group authorization, enable !- the aaa authorization commands. !- In order to enable Xauth for user authentication, !- enable the aaa authentication commands.
![how to setup router on a stick how to setup router on a stick](http://1.bp.blogspot.com/-VSGj2DByjv4/VO7bIXWo3LI/AAAAAAAAAVw/yymNl72oZDI/w1200-h630-p-k-no-nu/5.1.3.6%2BPacket%2BTracer%2B-%2BConfiguring%2BRouter-on-a-Stick%2BInter-VLAN%2BRouting%2BInstructions.jpg)
!- Enable authentication, authorization and accounting (AAA) !- for user authentication and group authorization. They are RFC 1918 addresses which have been used in a lab environment. Note: The IP addressing schemes used in this configuration are not legally routable on the Internet. Note: Use the Command Lookup Tool ( registered customers only) to obtain more information on the commands used in this section. In this section, you are presented with the information to configure the features described in this document. Refer to the Cisco Technical Tips Conventions for more information on document conventions. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment.
HOW TO SETUP ROUTER ON A STICK SOFTWARE
The information in this document is based on these software and hardware versions:Ĭisco Router 3640 with Cisco IOS® Software Release 12.4 There are no specific requirements for this document. This IP addressing scheme helps you to troubleshoot your network. Note: In order to avoid the overlapping of IP addresses in the network, assign the entirely different pool of IP addresses to the VPN Client (for example, 10.x.x.x, 172.16.x.x, .x). Refer to PIX/ASA 7.x and VPN Client for Public Internet VPN on a Stick Configuration Example in order to complete a similar configuration on a central site PIX Firewall. This allows the Internet traffic to be port address translated (PATed) to the outside world. In order to achieve this, configure the policy map in the router to point all the VPN traffic (Cisco VPN Client) to a loopback interface. This setup applies to a specific case where the router, without enabling split tunneling, and Mobile users (Cisco VPN Client) can access the Internet via the central site router.
HOW TO SETUP ROUTER ON A STICK HOW TO
This document describes how to set up a central site router to perform IPsec traffic on a stick.